Outside Plant Equipment

Grid View:
Quickview

Lift Plate / Guy Strap

Orders (0)
$6.95

Recommended for use behind the eyes of angled, thimbleye bolts with lag screws to increase load capacity either where loads are excessive or guys are steep. Distributes the load over a greater surface area, protecting the wood pole against shear damage. Plates measure 2 1/2" x 7", curved on a 3" radius. Plate used with 3/4" eyebolts have 7/8" x 1..

Quickview

LOCKING HEADS - T&B - PART# CSS-LH

Orders (0)
$4.25

LOCKING HEADS - T&B - 25 EA PER PACK - SOLD PER PACK..

Quickview

Loop Wall Strap

Orders (0)
$4.95

Formed from 1 7/32" x 15/64" steel. Used to terminate strand at a right angle to the building wall. A wire rope thimble is recommended to protect the strand. Overall length: 8". Part # 527284...

Quickview

Manual Hydraulic Compression Tool - EP-510C

Orders (0)
$1,575.00

Engineered to accommodate all "U" type dies currently used in existing 12-ton tools. One of Huskie's most versatile tools, since it takes a full range of connectors and lugs to 750 MCM. Jaw opening is 1.65" to accept larger splices up to 750 MCM. Midspan sleeve connection can be installed on these larger cables and the wire can then be removed t..

Quickview

Masonry Fastener - Type B

Orders (0)
$3.85

Used for mounting wire loops, cable clamps, gound blocks, terminals, ONI's, and protectors to mortar joints and weaker concrete. Includes an attached round washer. Made of formed AISI 1062 hardened steel and mechanically galvanized. Size: .145" x 1 1/4". Sold 12 per pack. Part # 400139929. Other sizes available upon request. Call TTG for mor..

Quickview

Masonry Fastener - Type C

Orders (0)
$1.80

Used for temporary installations of cable clamps, terminals, and protectors in mortar joints and weaker concrete. Each pin includes and attached round washer and hex nut. Formed from AISI 1062 hardened steel and mechanically galvanized. Size: 1 1/4" x 2". Sold 12 per pack. Other sizes available upon request. Call TTG for more information. Par..

Quickview

Nicopress Groove Tool, 31-DC

Orders (6)
$236.25

Nicopress Groove Tool is designed for use with FW-type sleeves, 12 1/2 ga and 14 1/2 ga wire. Part # 31-DC...

Quickview

OSP Combi Cord - TC-OSPACGN

Orders (17)
$119.00

This OSP Combi Cord is configured with Clip Access/RJ11 jack to 110 plug, 66 Block, 526A, 463A. Length: 1 ft. Part # TC-OSPACGN...

Quickview

OSP Combi Cord - TC-OSPCEFH

Orders (1)
$112.00

This OSP Combi Cord is configured with a Clip Access / RJ 11 jack to 66 Block, Binding Post, Dat-term, and Self-Strip ends. Length: 1 ft. Part # TC-OSPCEFH...

Quickview

OSP Combi Cord - TC-OSPCNP

Orders (0)
$112.00

OSP Combi Cord is configured with Clip Access/RJ11 jack to RJ11, 66 Block and 463A. Length: 1 ft. Part # TC-OSPCNP...

Quickview

OSP Combi Cord - TC-OSPDEGH

Orders (0)
$112.00

This OSP Combi Cord is configured with Clip Access/RJ11 jack to Self-Strip connector, Binding Post Clip, 526A and Krone connector. Length: 1 ft. Part # TC-OSPDEGH...

Quickview

OSP Combi Cord - TC-OSPDKNM

Orders (1)
$112.00

This OSP Combi Cord configured is with Clip Access/RJ11 jack to 463A, Porta, Krone, BIX. Length: 1 ft. Part # TC-OSPDKNM...

Quickview

OSP Combi Cord - TC-OSPEFHQ

Orders (0)
$112.00

This OSP Combi Cord is configured with Clip Access/RJ11 jack to RJ11, Binding Post clip, Dat-term, and Self-Strip connector. Length: 1 ft. Part # TC-OSPEFHQ...

Quickview

OSP Combi Cord, TC-OSPAENQ

Orders (0)
$112.00

The OSP Combi Cord is configured with Clip Access/RJ11 jack to 110 plug, 66 Block, Binding Post clip, 463A. Reduce truck rolls by having the test plugs you need on a single 1 foot cord. Part #: TC-OSPAENQ...

Quickview

Paint Wand / Ground Marker

Orders (0)
$19.90

Easy to use wand has light touch control. Length: 2 1/2' long. Holds 16 oz or 20 oz cans of inverted marking paint. Ideal for surveyors, contractors, or anyone needing to mark ground locations. Designed for all stripe-inverted tip marking paints. Part # Z-606...

Showing 61 to 75 of 110 (8 Pages)